← Back to BlogAdvice

Is My Wall Load Bearing? How to Tell Before You Call Anyone

17 October 2026

If you're planning to open up a kitchen, knock two rooms into one, or just get more light into a dark hallway, the first question is always the same: is that wall load bearing?

It's a fair thing to wonder about before you spend money on anyone. There are a few signs you can look for yourself, and we'll go through them below. But one thing up front: none of this is a substitute for a structural engineer. Think of it as getting your head round the job, not making the call.

Why it matters

A load bearing wall is carrying weight from something above it. That might be the floor above, the roof, or another wall. Take it out without proper support and you can get sagging floors, cracked plaster, doors that stop closing, and in the worst cases a partial collapse.

A non-load-bearing wall (a partition) is just dividing a space. It can usually come out much more simply. The trouble is the two can look identical from the room.

Signs a wall might be load bearing

None of these is proof on its own. Together they give you a decent steer.

Which way do the joists run?

Floor joists are the timbers that hold up the floor above. If they run across a wall (at right angles to it), that wall may well be holding them up. If they run parallel to the wall, it's less likely to be carrying them, though not impossible.

Is it an external wall?

External walls are nearly always load bearing. Treat them that way unless an engineer tells you otherwise.

Is it in the middle of the house?

A wall running roughly down the centre of the property often supports the floor joists or roof above. Spine walls like this are a classic one to watch for.

How thick is it?

Thicker walls are more likely to be structural. A wall that sounds hollow when you knock on it and is only around 100mm thick is often a timber stud partition. A solid, thick wall is a different story. Mind you, thickness alone can mislead: some thin walls carry load and some chunky ones don't.

What's above and below it?

Walls tend to stack. If there's a wall directly above this one upstairs, or a wall directly below it downstairs, the chances are higher that it's part of the structure carrying load down to the foundations.

Old stone and brick versus modern partitions

Older Edinburgh and East Lothian properties are often solid stone or brick, and internal walls in these houses can be structural in ways that aren't obvious. A lot of newer homes use timber-frame construction, with plasterboard partitions that are mostly non-structural, but not always. Don't assume based on age alone.

Tenements and flats in Edinburgh

Edinburgh's tenements deserve a special mention. In a tenement flat, the walls often carry load not just for your flat but for the ones above. A wall that looks like a simple divider could be supporting the floors, and the neighbours, over your head.

That brings a few extra things to think about:

  • Walls and floors in a tenement can be shared or affect other owners, so you may need to consult neighbours or check your title deeds.
  • Work to a flat can affect the flats above and below, so it needs to be properly designed.
  • Chimney breasts and gables often carry a lot more than they look like they do.

An engineer will account for all of this, which is another reason not to guess.

What you can safely check yourself

You're not doing any damage with these.

  • Look in the loft. If you can safely get to it, see which way the ceiling joists and roof timbers run, and whether they rest on the wall in question. Only step on the joists or boarded areas, never between them.
  • Check under the floor. If you have a cellar or accessible sub-floor, see whether the wall sits on a wall or support below.
  • Find the plans. Original drawings, previous alteration paperwork, or your Building Warrant history can show how the house was built and what's been changed. The local council's Building Standards team may hold records for your property.
  • Check the floor above. Compare the layout upstairs to the wall downstairs. Is there something sitting right on top of it?

If you're not comfortable going into a loft or lifting boards, leave it. It isn't worth getting hurt over.

Why you should never just knock it to find out

We get it: it's tempting to put a hole in the plaster and see. Don't.

If the wall is carrying load, removing even part of it can bring things down on you. It's not only the wall that matters but the dust, the damage, and the cost of fixing a problem you've created. Also, opening up a structural wall without the right sign-off can cause trouble down the line, including when you come to sell.

Stripping plaster back or lifting a floorboard to have a look is one thing. Taking a hammer to the wall itself is another.

What to do next

If you think the wall is load bearing, or you're not sure, here's the sensible route.

  1. Appoint a structural engineer. They'll confirm whether the wall is load bearing, and if it is, calculate and specify the steel beam (RSJ) and supports needed to take the load safely.
  2. Building Warrant. Removing a structural wall normally needs a Building Warrant from your local council's Building Standards team. In most cases the engineer or architect submits this, not the builder.
  3. Get the work built to the engineer's spec. That's where we come in. We build to what the engineer specifies, from the temporary supports and steel installation through to making good.

You appoint your own engineer. If you don't have one, we're happy to recommend people we trust, but the appointment is yours.

FAQ

Can I remove a load bearing wall in my Edinburgh flat?

Often yes, but it needs an engineer's design, usually a Building Warrant, and in a tenement you'll need to think about neighbours and your title deeds. Don't start until all of that is in place.

Is a thin wall always non-load-bearing?

No. Thin walls can carry load, especially in older properties, and some thick walls carry nothing. That's why a visual check can only ever be a rough guide.

Who do I speak to first, a builder or an engineer?

If you're serious about the job, you need an engineer to confirm the wall and specify the beam. A builder can talk through what's involved and what's realistic, but the engineer's design is what the work gets built to.

Planning to open up a wall?

We do structural openings, steel beam and RSJ installation, and strip-out across Edinburgh, East Lothian and Midlothian, from our base at Fenton Barns, North Berwick. If you've got an engineer's spec, or you're still working out where to start, get in touch.

Request Your Free Quote
CallGet a Free Quote