← Back to BlogAdvice

Chimney Breast Removal Cost in Edinburgh: What Actually Affects the Price

19 November 2026

A chimney breast takes up a lot of room, and in a lot of Edinburgh homes it's the one thing stopping the living room or bedroom working properly. Taking it out is a very common job. It's also one where the price can vary a lot, and where cutting corners causes real problems.

We won't pretend there's a standard figure. Every chimney is different. What we can do is explain what drives the cost so you know what you're being quoted for and can compare quotes properly.

What a chimney breast actually is

The chimney breast is the part of the wall that sticks out into the room and carries the flue up to the chimney stack on the roof. Even if the fireplace has been blocked up for years, the breast is often still holding up the brickwork or stone above it, sometimes all the way to the roof.

That's why you can't treat it like a stud partition. If the breast comes out, whatever it was carrying has to be supported some other way.

The main ways a chimney breast comes out

Full removal, floor to ceiling and stack as well

The breast, the flue and the stack above roof level are all taken out, and the roof is made good. This is the biggest job, but it deals with the whole thing and leaves no stack to maintain.

Removing the breast but keeping the stack

Often the stack stays for appearance, to keep a shared chimney, or because it's a feature of the building. The breast below is removed and the stack above is held up on steelwork. The engineer designs this, and it's usually what's meant by a "chimney breast gather" or supporting the stack with a steel beam and supports.

Removing it on one floor only

If the breast continues up through other rooms, taking it out in just one room means the part above still needs to be carried. Again, this is steelwork designed by the engineer.

What affects the cost

  • How much is coming out. One room or several floors, and whether the stack is going too.
  • The support. Steel beams, brackets and padstones are specified by the engineer. Heavier loads and longer spans mean more steel and more work to fit it.
  • Access. Upper floors, tight stairs, no parking close by, or working from a roof all make it slower.
  • The property. Solid stone and old brick behave differently from newer construction, and what's behind the plaster isn't always what you expected.
  • Roof work. If the stack is coming down, the roof has to be made weathertight afterwards.
  • Making good. Patching floors, ceilings and walls, and re-plastering. Some people want it all finished, others have a decorator booked.
  • Waste. A chimney breast produces a lot of rubble, and getting it out and away isn't free.
  • Professional fees. The engineer and the Building Warrant are separate from the building work. Your own engineer is appointed by you.

Be careful of very low quotes. A cheap price for a chimney breast often means no engineer's design, no proper support for the stack, or a hole in the finish that you pay for later.

Why the engineer comes first

Before anyone prices the building work properly, you need to know what the breast is carrying. A structural engineer looks at the chimney, what's above, and the surrounding walls and floors, then specifies the steelwork and supports. Building work is priced against that design, and the Building Warrant application is based on it.

If you want the full picture on this, our guide on when you need a structural engineer goes through it.

Tenements and shared stacks

In an Edinburgh tenement, the chimney stack often serves several flats. The flue from your breast might join others, and the stack above you may be carrying your neighbours' chimneys too. Before work starts:

  • Check your title deeds and any shared maintenance agreements.
  • Speak to the neighbours who share the stack.
  • Make sure the engineer's design takes the shared flues into account.

Things people forget

  • Other flues. If the chimney serves a boiler or another fireplace, the flue still needs to work properly afterwards.
  • Ventilation. Capped or left-over flues need to be ventilated correctly, and your engineer or Building Standards can advise.
  • Dust and mess. Taking out a breast is dusty work. We protect the rest of the house, but expect disruption in that part of the property.
  • Floor and ceiling repairs. There's usually a gap where the breast sat. Decide in advance who's doing the finish.
  • Hidden surprises. Old fireplaces sometimes hide debris, old soot, or materials that need careful handling. A site visit helps flag these.

What happens when you contact us

  1. Site visit. We look at the chimney breast and the property with you, free of charge.
  2. Engineer. You appoint a structural engineer to design the support. If you don't have one, we can recommend people we trust.
  3. Building Warrant. Sorted through your engineer or architect before work starts.
  4. Quote. Based on the engineer's design and what we saw on site.
  5. The work. Temporary supports, steel installation, breast removal, and making good to the agreed finish.

FAQ

How much does it cost to remove a chimney breast in Edinburgh?

It depends on the job. The biggest factors are whether you're taking out the breast on one floor or several, whether the chimney stack above has to be supported, the steelwork the engineer specifies, access, and how much making good is needed. We don't give a price without seeing the property. We'll visit, look at it with you, and quote based on the engineer's design.

Do I need a structural engineer to remove a chimney breast?

Yes. The stack above is heavy and often carries more than it looks like it does. An engineer confirms what's above, designs the support, and specifies the steelwork the job gets built to.

Do I need a Building Warrant to remove a chimney breast in Scotland?

Usually yes, because it's structural work. Your engineer or architect normally sorts the application with your local council's Building Standards team. Check before work starts rather than after.

Can I remove a chimney breast in a tenement flat?

Often yes, but a tenement chimney stack can serve the flats above and next door, and the flues may be shared. You'll need the engineer's design, and you should check your title deeds and speak to neighbours first.

Thinking about removing a chimney breast?

We do structural openings, steel beam and RSJ installation, and strip-out across Edinburgh, East Lothian and Midlothian. Get in touch and we'll arrange a free site visit.

Request Your Free Quote
CallGet a Free Quote